dye classunder review

reactive dye

Also known as: fiber reactive dye, fibre-reactive dye

A class of water-soluble dyes that colour fibre by forming a covalent bond with it.

What is shown here is what the sources say; it is not instructions for use. For any individual product, see its label and safety data sheet.

日本語版

Claims and evidence (75)

The limitations noted for some sources are recorded in Japanese only — see the Japanese edition.

reactive dye bonds via dyeing by covalent bondingcontextual
States that dyeing occurs through a covalent bond formed between dye and fibre.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文1文目 ・institutional summary ・ checked against the source by AI
Says the dyes attach permanently to cellulose fibres by a covalent (electron-sharing) bond, and that the reaction happens gradually over time depending on temperature and/or pH.
Source: Tie-Dye Instructions (Dharma Trading Co.) ・化学の説明の段落("attach permanently ... covalent") ・manufacturer statement ・ checked against the source by AI
The paper places fibre-dye bonding for cellulosic-fibre dyes into three modes (citing ref. 1) and states that reactive dyes bond via the most stable, highest-energy of the three (covalent bonding), which gives excellent wet fastness.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
In a summary table of reactive-dye properties, lists the bond type as "covalent" and the character as "anionic (forms a colloidal solution)".
Source: 反応染料(上級編) (岩瀬商店株式会社(ソメラボ), 2020) ・「反応染料のまとめ」の表 ・manufacturer statement ・ checked against the source by AI
reactive dye requires alkalicontextual
Describes taking up dye from the bath, then adding alkali so dye and fibre bond by chemical reaction.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文2文目 ・institutional summary ・ checked against the source by AI
States that alkali addition is needed to promote the reaction between fibre and dye; in exhaust dyeing the optimum pH is about 11-12, with about pH 11.5 for the mid-temperature type.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P122 §2.5(1) ・textbook ・ checked against the source by AI
reactive dye is soluble in watercontextual
States that the dye dissolves in water.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文「水に溶解」 ・institutional summary ・ checked against the source by AI
reactive dye is applicable to cellulosic fibrescontextual

Scope: As stated on Kaken's short explainer page (no test conditions or sources are given) and in a lecture-column series in a textile-machinery society journal (Imada, Part 3, 2002). The two differ on nylon

Lists cellulosic fibres (cotton, linen, rayon, polynosic, cupro, lyocell etc.), wool and silk as dyeable.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文「…に染色可能」 ・institutional summary ・ checked against the source by AI
States that reactive dyes are used to dye cellulosic fibres such as cotton, linen/hemp and rayon.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119-P120 §2.1 ・textbook ・ checked against the source by AI
reactive dye is applicable to woolcontextual
Lists cellulosic fibres (cotton, linen, rayon, polynosic, cupro, lyocell etc.), wool and silk as dyeable.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文「…に染色可能」 ・institutional summary ・ checked against the source by AI
States that reactive dyes are also used on wool, and that new wool-specific reactive dyes have recently appeared using reactive groups originally developed for cellulosic fibres.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119-P120 §2.1, §2.4 ・textbook ・ checked against the source by AI
reactive dye is applicable to silkcontextual
Lists cellulosic fibres (cotton, linen, rayon, polynosic, cupro, lyocell etc.), wool and silk as dyeable.
Source: 反応染料 (一般財団法人カケンテストセンター) ・本文「…に染色可能」 ・institutional summary ・ checked against the source by AI
States that reactive dyes are also used to dye silk.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119-P120 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・property ― silkcontextual

Scope: Dharma fibre reactive dyes

Says colours may shift on silk: blue does not combine well with silk, so mixes with blue shift toward the other colours (black to brown or maroon, purple to raspberry, forest green to chartreuse).
Source: Dharma's Fiber Reactive MX Dyes FAQ (Dharma Trading Co.) ・絹についての回答 ・manufacturer statement ・ checked against the source by AI
Says fibre reactive colours shift on protein fibres and a true black cannot be obtained.
Source: Tie-Dye Instructions (Dharma Trading Co.) ・絹・毛のタイダイの段落 ・manufacturer statement ・ checked against the source by AI
all-purpose dye differs from reactive dyecontextual
Says soda ash will not make all-purpose dye such as Rit permanent; use a washfast dye such as Procion MX, which does require soda ash, or a commercial cationic fixative.
Source: What is soda ash, and what's it for in dyeing? (Paula E. Burch, 2015) ・"Do we need to use soda ash with Rit dye?" ・practitioner's record ・ checked against the source by AI
reactive dye ・mechanismin tub dyeing, salt and dye load the fabric, then dissolved soda ash raises the pH; the reaction takes about an hour to occur fullycontextual

Scope: Tub (immersion) dyeing

Says salt and dye load the fabric, adding dissolved soda ash raises pH and makes the colour permanent, and the reaction takes about an hour to occur fully.
Source: Dharma's Fiber Reactive MX Dyes FAQ (Dharma Trading Co.) ・浸染の説明の段落 ・manufacturer statement ・ checked against the source by AI
reactive dye ・propertyfirst announced in 1956, the newest dye class among the major categoriescontextual
States that reactive dyes were announced in 1956, the newest dye class; no inventor or company is named.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyspans shades from bright to deep and has overtaken direct and sulfur dyes to become the highest-volume class of dye for cellulosic fibrescontextual

Scope: Dyes for cellulosic fibres

States that because reactive dyes span a wide range of shades from bright to deep colours, they have replaced direct and sulfur dyes to become the highest-volume class of dye for cellulosic fibres.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertycolours are bright/clearcontextual
Lists as a strong point of reactive dyes: colours are bright/clear.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertywet fastness (to water, perspiration, washing, etc.) is goodcontextual
Lists as a strong point of reactive dyes: wet fastness (to water, perspiration, washing, etc.) is good.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertythe dyeing procedure is relatively easycontextual
Lists as a strong point of reactive dyes: the dyeing procedure is relatively easy.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertycan be applied by exhaust dyeing relatively easily at low temperaturecontextual
Lists as a strong point of reactive dyes: can be applied by exhaust dyeing relatively easily at low temperature.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertysolubility is generally good, and many are well suited to printingcontextual
Lists as a strong point of reactive dyes: solubility is generally good, and many are well suited to printing.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertytend to stain unprinted (white) ground less in printingcontextual
Lists as a strong point of reactive dyes: tend to stain unprinted (white) ground less in printing.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertymany can be used in discharge and resist-discharge printingcontextual
Lists as a strong point of reactive dyes: many can be used in discharge and resist-discharge printing.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyexisting dyeing equipment can be usedcontextual
Lists as a strong point of reactive dyes: existing dyeing equipment can be used.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertymany have weak chlorine fastnesscontextual
Lists as a weak point of reactive dyes: many have weak chlorine fastness.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertysome have weak lightfastness and weak perspiration-light combined fastnesscontextual
Lists as a weak point of reactive dyes: some have weak lightfastness and weak perspiration-light combined fastness.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyfor some dyes using certain reactive groups, the fibre-dye bond changes over time and wet fastness declinescontextual
Lists as a weak point of reactive dyes: for some dyes using certain reactive groups, the fibre-dye bond changes over time and wet fastness declines.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyin exhaust dyeing the degree of fixation is often comparatively low, giving strongly coloured dyeing effluentcontextual

Scope: Exhaust dyeing

Lists as a weak point of reactive dyes: in exhaust dyeing the degree of fixation is often comparatively low, giving strongly coloured dyeing effluent.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyexhaust dyeing requires a large addition of inorganic saltcontextual

Scope: Exhaust dyeing

Lists as a weak point of reactive dyes: exhaust dyeing requires a large addition of inorganic salt.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertybecause substantivity (affinity) is low, dyeing is sensitive to the liquor ratiocontextual
Lists as a weak point of reactive dyes: because substantivity (affinity) is low, dyeing is sensitive to the liquor ratio.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI
reactive dye is applicable to nyloncontextual

Scope: As stated in a lecture-column series for dyeing technicians in a textile-machinery society journal. The fibres listed on Kaken's reactive-dye page do not include nylon

States that reactive dyes are also used to dye nylon.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119-P120 §2.1 ・textbook ・ checked against the source by AI
reactive dye is applicable to polyestercontextual

Scope: Polyester/cellulosic-fibre blends and unions

States that in polyester/cotton and polyester/rayon blends and unions, reactive dyes are used to dye and print the cellulosic-fibre side.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119-P120 §2.1 ・textbook ・ checked against the source by AI
reactive dye ・propertyreactive groups are classified by chemical structure into three types: aliphatic-carrier groups (vinyl-sulphone type), heterocyclic-carrier groups (mainly triazine and pyrimidine types), and bifunctional types carrying two or more different reactive groupscontextual
States that industrially used reactive groups can be classified by chemical structure into three types: aliphatic (vinyl-sulphone type), heterocyclic (mostly triazine-type), and bifunctional types carrying two or more different reactive groups.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P120 §2.2(1) ・textbook ・ checked against the source by AI
reactive dye ・propertyabout 95% of reactive dyes currently on the market for cellulosic fibres are vinyl-sulphone, triazine or pyrimidine type, or bifunctional combinations of thesecontextual

Scope: Commercial reactive dyes for cellulosic fibres

States that about 95% of commercial reactive dyes for cellulosic fibres fall into the vinyl-sulphone, triazine or pyrimidine types, or bifunctional combinations of these.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P120 §2.2(1) ・textbook ・ checked against the source by AI
reactive dye ・mechanismgiven this reactivity difference, reactive dyes are thought to react mainly with the primary OH group at C6contextual

Scope: Cellulosic fibre

States that, given this reactivity difference, reactive dyes are thought to react mainly with the primary OH group at C6 (citing ref. 3).
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P120 §2.2(2) ・textbook ・ checked against the source by AI
reactive dye ・mechanismthe reaction mechanism with cellulosic fibre is broadly divided into nucleophilic addition and nucleophilic substitutioncontextual

Scope: Cellulosic fibre

States that the reaction mechanism of reactive dyes with cellulosic fibre falls into two broad types: nucleophilic addition and nucleophilic substitution.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P120-P121 §2.2(2) ・textbook ・ checked against the source by AI
reactive dye works by hydrolysis (of reactive dye)contextual

Scope: Cellulosic fibre, under practical dyeing conditions

States that fixation (reaction with fibre) competes with hydrolysis (reaction with water), but under practical dyeing conditions the fibre reaction proceeds preferentially.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P121 §2.2(2) ・textbook ・ checked against the source by AI
reactive dye ・property ― degree of fixation (fixation rate)contextual

Scope: Deep-shade dyeing

States that for deep-shade dyeing etc., the reactive fixation rate can be as low as about 50%, and various measures are taken to raise it.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P121 §2.2(2) ・textbook ・ checked against the source by AI
reactive dye ・mechanismthree measures for raising the fixation rate are given: adopting a more reactive reactive group (e.g. changing monochlorotriazine to monofluorotriazine), introducing multiple reactive groups into one dye molecule (including bifunctional types), and introducing two chromogens to raise the dye's affinity for the fibrecontextual
Lists three measures for improving fixation rate: (1) using a more reactive reactive group (e.g. switching monochlorotriazine to monofluorotriazine), (2) introducing multiple reactive groups (same or bifunctional types) into one molecule, and (3) introducing two chromogens into the dye molecule to raise fibre affinity.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P121 §2.2(2) ・textbook ・ checked against the source by AI
reactive dye works by hydrolysis (of reactive dye)contextual

Scope: Exhaust dyeing

States that dyeing above the optimum temperature favours hydrolysis and lowers fixation, while dyeing too far below it slows the fibre reaction and leaves fixation insufficient.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P122 §2.5(1) ・textbook ・ checked against the source by AI
reactive dye ・propertyclassified by reactivity level into low-temperature type (40-50°C), mid-temperature type (60°C), and high-temperature type (70-90°C)contextual

Scope: Exhaust dyeing

Gives approximate dyeing temperatures: low-temperature type 40-50°C, mid-temperature type 60°C, high-temperature type 70-90°C.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P122 §2.5(1) ・textbook ・ checked against the source by AI
reactive dye requires inorganic salt (exhaust-dyeing electrolyte)contextual

Scope: Exhaust dyeing

States that because reactive dyes have smaller molecules and lower fibre affinity than direct dyes, they need relatively large amounts of salt (manufacturers recommend about 50-80 g/l), though higher-affinity low-salt-type dyes need only about 25-40 g/l.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P122-P123 §2.5(1) ・textbook ・ checked against the source by AI
reactive dye ・propertybecause affinity is low, dyeing is sensitive to the liquor ratio, and a lower liquor ratio gives a higher fixation ratecontextual

Scope: Exhaust dyeing

States that because reactive dyes have low affinity, they are sensitive to the liquor ratio, with a lower liquor ratio giving a higher fixation rate.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P123 §2.5(1) ・textbook ・ checked against the source by AI
reactive dye requires soaping (wash-off of unfixed reactive dye)contextual
States that although reactive-dyed fabric is known for good wet fastness, before soaping, hydrolysed dye that never bonded to the fibre remains and wet fastness is poor, so thorough soaping is needed to remove it.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P123 §2.5(1)(2) ・textbook ・ checked against the source by AI
reactive dye ・propertywear and washing of reactive-dyed fabric can cause discoloration or dye bleeding that leads to consumer complaints, indicating a chemical change in the dye chromogen, the fibre-dye bond, or bothcontextual
States that reactive-dyed cellulosic products can discolour or bleed colour during wear or washing, causing consumer complaints, and that such trouble indicates a chemical change in the dye's chromogen, the fibre-dye bond, or both.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P125-P126 §2.6 ・textbook ・ checked against the source by AI
reactive dye ・propertyhigh-fastness reactive dyes are designed by combining a chromogen stable to light and oxidising agents with a reactive group that gives a fibre-dye bond stable to acid gas, heat and oxidising agentscontextual
States that high-fastness reactive dyes are made by combining a chromogen resistant to light and oxidising agents with a reactive group that gives a fibre-dye bond resistant to acid gas, heat and oxidising agents.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P126 §2.6 ・textbook ・ checked against the source by AI
reactive dye ・propertythe reactive group can also react with amino groups on blood proteins; if dye that has retained its reactivity is taken into the body, it can bond to those amino groups and cause allergic sensitisation, and inhaling dye dust can sensitise the respiratory tract in a way that can be life-threatening, so major manufacturers use warning labelscontextual

Scope: Weighing and dissolving dye in a dyeing plant

States that the reactive group can also react with amino groups on blood proteins, so dye that enters the body while still reactive can cause allergic sensitisation; inhaling dye dust can sensitise the respiratory tract and be life-threatening, so major manufacturers label products with EU precaution code S22 (do not breathe dust).
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P126 §2.7(1) ・textbook ・ checked against the source by AI
reactive dye ・regulationmetal-complex reactive dyes containing copper or chromium fall under Japan's Industrial Safety and Health Act notification list; under Japan's PRTR Act, copper-containing dyes are exempt but chromium-containing dyes are covered, though very few reactive dyes contain chromiumcontextual

Scope: Dyeing plants in Japan

States that metal-complex dyes containing copper or chromium fall under the Industrial Safety and Health Act notification list, with widely used copper-phthalocyanine bright-blue dyes needing particular attention; under the PRTR Act copper-containing dyes are exempt but chromium-containing ones are covered, though very few reactive dyes contain chromium.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P126 §2.7(3) ・textbook ・ checked against the source by AI
reactive dye ・mechanismin the reaction schemes the cellulose partner is drawn as "⁻O–Cell" (oxygen bearing a negative charge), which reacts with the dye's reactive groupcontextual

Scope: Schemes for the vinyl sulphone type (nucleophilic addition) and the monochlorotriazine type (nucleophilic substitution)

In both schemes cellulose appears as ⁻O–Cell; for the vinyl sulphone type the scheme also shows HO⁻ generating the vinyl sulphone group. The running text does not say in words that alkali converts the cellulose OH into this form.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P120 §2.2(2) 反応機構の式①② ・textbook ・ checked against the source by AI
reactive dye ・propertythe level of reactivity wanted depends on the dyeing method: high reactivity for cold pad-batch and relatively low-temperature exhaust dyeing; relatively low reactivity is often wanted for printing because of print-paste storage stabilitycontextual
Says cold pad-batch and relatively low-temperature exhaust dyeing call for highly reactive dyes, while printing often calls for relatively low reactivity because of print-paste storage stability.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P122 §2.3「反応染料の染色性による分類」 ・textbook ・ checked against the source by AI
Reac dye is a type of reactive dyecontextual
States that Reac dye is a reactive dye that can dye cotton, hemp and rayon.
Source: カラー見本比較表【リアック染料】 (田中直染料店) ・「リアック染料とは」の段落、1文目 ・manufacturer statement ・ checked against the source by AI
"Remazol" type reactive dye is a type of reactive dyecontextual
Describes the "Remazol" type as a reactive dye characterised by vivid colour that does not require steaming.
Source: 藍熊染料の講習会(一覧頁) (藍熊染料株式会社) ・「レマゾールタイプ染料の基礎」講習会の説明文 ・manufacturer statement ・ checked against the source by AI
States that Remazol dye is a reactive dye developed to dye cellulosic fibres such as cotton and hemp.
Source: レマゾール染料 (ミムラセンリョウ株式会社) ・「レマゾール染料の特徴」の段落、1文目 ・manufacturer statement ・ checked against the source by AI
reactive dye ・mechanismgives an example industrial immersion recipe of a 1:20 liquor ratio and 60°C for 40 minutes: dye is dissolved into a 40°C bath, the fabric is added, Glauber's salt is added 10 minutes later, soda ash a further 10 minutes after that, the bath is then raised to 60°C over about 10 minutes, and dyeing continues for 40 minutescontextual

Scope: Iwase Shoten (Somelabo)'s example reactive-dye recipe

Shows an example recipe of a 1:20 liquor ratio and 60°C for 40 minutes: put the dissolved dye into a 40°C dye liquor, add the fabric, add the Glauber's salt 10 minutes after the dye, add the soda ash a further 10 minutes later (all at 40°C so far), raise to 60°C over about 10 minutes, then dye for 40 minutes with good agitation.
Source: 反応染料(上級編) (岩瀬商店株式会社(ソメラボ), 2020) ・「反応染料の染色工程」【染色処方】の手順1〜5 ・manufacturer statement ・ checked against the source by AI
post-dyeing colour-fixing agent is applicable to reactive dyecontextual

Scope: regarding fibre-reactive dye that has been alkali-fixed and thoroughly washed out

States that fibre-reactive dye, once properly fixed and washed, needs no further treatment with Retayne or a similar product.
Source: Is there a fixative that will make dye permanent? What is Retayne? (Paula E. Burch, 2011) ・見出し「Should Retayne be used for fiber reactive dyes?」 ・practitioner's record ・ checked against the source by AI
post-dyeing colour-fixing agent is used in reactive dyecontextual

Scope: regarding industrial dyeing with fibre-reactive dye

States that where water is scarce, reaching for a cationic fixative can work out cheaper than the water a full wash-out would take.
Source: Is there a fixative that will make dye permanent? What is Retayne? (Paula E. Burch, 2011) ・見出し「Should Retayne be used for fiber reactive dyes?」 ・practitioner's record ・ checked against the source by AI
NEOFIX series is applicable to reactive dyecontextual
Tabulates three types of fixing agent for reactive dyes: a high-fastness type, a water-absorbing type, and a chlorine-fastness-focused type.
Source: 繊維用界面活性剤に関して(界面活性剤講座 第11講) (齋藤嘉孝(日華化学株式会社), 2017) ・P83 表-5「セルロース用フィックス剤のタイプ」 ・textbook ・ checked against the source by AI
post-dyeing colour-fixing agent differs from reactive dyecontextual

Scope: regarding differences between reactive-dye types in how hard it is to wash out unattached dye

States that, unlike Procion MX, fibre-reactive dyes such as Cibacron F and Drimarene K do not take as much work to rinse out the excess unattached dye.
Source: Is there a fixative that will make dye permanent? What is Retayne? (Paula E. Burch, 2011) ・見出し「Should Retayne be used for fiber reactive dyes?」の末尾 ・practitioner's record ・ checked against the source by AI
reactive dye requires soda ash (sodium carbonate)contextual

Scope: as described for home-studio batik in the US using Procion MX dye

this practitioner states soda ash fixes Procion dye in room-temperature water, with no need for hot water that would melt the wax
Source: How to Batik (Paula E. Burch, 1999) ・"Materials for making batik" リスト内 "Soda Ash Dye Fixer"の項 ・practitioner's record ・ checked against the source by AI
reactive dye differs from naphthol (azoic) dyecontextual

Scope: as described for choosing a dye for home-studio batik in the US

this practitioner states it allows cool water unlike all-purpose dye, and is reasonably non-toxic unlike naphthol dye
Source: How to Batik (Paula E. Burch, 1999) ・"How to Batik"導入段落 ・practitioner's record ・ checked against the source by AI
reactive dye ・propertyStates reactive dyes, alongside acid dyes, are much more lightfast (in contrast with Basic dyes)contextual
States acid and reactive dyes are much more lightfast (than Basic dyes).
Source: Lightfastness of Different Types of Dyes (Paula E. Burch, 2011) ・「Which dyes are more or less lightfast?」 ・practitioner's record ・ checked against the source by AI
reactive dye ・propertyThe same Table 1 describes reactive dyes for wool as having reactive groups with 1-3 sulfonic acid groups and no metal, giving vivid-to-deep colours with good wet fastness.contextual

Scope: Reactive dyes for wool (Imada part 6, Table 1; the other three types in the table are for polyamide fibres generally, but this type is distinguished in the table as wool-specific)

The "Reactive dye for wool" row of Table 1 gives chemical structural characteristics as "has reactive groups", sulfonic acid groups "1-3", metal "none", and characteristics/use as "vivid to deep colours / good wet fastness".
Source: 染色技術者のための染料化学(その6)6. ポリアミド繊維用染料 6.1 酸性染料 (今田邦彦, 2002) ・誌面P358 表1「ポリアミド繊維用染料の特徴と用途」(PDF頁1/5、300dpiの頁画像で確認) ・textbook ・ checked against the source by AI
naphthol (azoic) dye differs from reactive dyecontextual

Scope: for dyeing on cotton

States azoics have a more limited shade range and more complex process than reactive dyes but better chlorine fastness, that rubbing and light fastness are better with reactive dyes, and that dark, bright reds, maroons and oranges which are difficult with reactive dyes are possible with azoics.
Source: Naphthols and Bases (hanu(ブログ「Dyeing and Processing / dyeing world」運営者名として表示), 2010) ・Reactive Vs Azoics節 ・practitioner's record ・ checked against the source by AI
reactive dye ・mechanismStates the basic dye structure takes the form D-T-X (D: chromophore, T: linking group, X: reactive group), giving triazine, pyrimidine, and sulphatoethylsulphone (vinyl sulphone) groups as representative examples of the reactive group Xcontextual
States reactive dyes covalently bond to hydroxyl groups in cellulose, with the basic dye structure taking the form D-T-X (D: chromophore, T: linking group, X: reactive group), giving triazine, pyrimidine, and sulphatoethylsulphone (vinyl sulphone) groups as representative reactive-group examples.
Source: 連載〈やさしい繊維基礎講座〉染色 (高岸徹, 2003) ・P_360 §7.1 セルロース系繊維、反応染料の段落(図5・図6) ・textbook ・ checked against the source by AI
reactive dye ・mechanismStates that the terminal amino group of nylon can be dyed by reactive dyes through covalent bondingcontextual

Scope: polyamide fiber (nylon)

States that reactive dyes can dye nylon via covalent bonding to the fiber's terminal amino group.
Source: 連載〈やさしい繊維基礎講座〉染色 (高岸徹, 2003) ・P_361 §7.4.1 ポリアミド繊維、末尾の一文 ・textbook ・ checked against the source by AI
reactive dye ・mechanismThe reactive-ink printing process is described as: alkali needed for the dye-cellulose reaction is applied to the fabric during pretreatment, the dye is then covalently bonded to the fibre during steaming, and unreacted dye is removed during washing.contextual

Scope: reactive-ink inkjet textile printing

Figure-1 shows the reactive-ink workflow as pretreatment, printing, high-temperature steaming, rinse, soaping, warm rinse and rinse, explaining alkali is applied during pretreatment and covalent bonding occurs during steaming.
Source: デジタルテキスタイル用色材 (城田衣(キヤノン株式会社 総合R&D本部), 2015) ・3.1 プリント工程、図-1 ・textbook ・ checked against the source by AI
reactive dye ・applies toMimaki's reactive-dye ink (SPC-0357xx series) is listed with cotton as its corresponding fabric.contextual

Scope: Mimaki's own dye-ink product guidance

The table lists cotton as the applicable fabric for the SPC-0357xx series (reactive-dye ink).
Source: 捺染インク 使用ガイダンス(TX23シリーズ) (株式会社ミマキエンジニアリング) ・2. 対応メディアとインクの種類、表 ・manufacturer statement ・ checked against the source by AI
reactive dye ・propertyReactive ink is said to have a shorter shelf life -- one to one-and-a-half years -- than other ink types, partly because the dye's reactive group can hydrolyse with water in the ink during storage, or lose reactivity through side reactions with the humectant.contextual

Scope: storage stability of reactive ink

States the reactive-ink shelf life is currently one to one-and-a-half years, shorter than other ink types, explaining hydrolysis of the reactive group or side reactions with the humectant during storage as one cause.
Source: デジタルテキスタイル用色材 (城田衣(キヤノン株式会社 総合R&D本部), 2015) ・3.4.1 インクの保存性 ・textbook ・ checked against the source by AI
reactive dye ・propertyMonochlorotriazine (MCT) is said to be the most widely used reactive group for digital-textile reactive dye, with the vinyl-sulphone (VS) type C.I. Reactive Black 5 widely used for deep black. Both bond to cellulose's OH groups in the presence of alkali, but for ink storage stability, MCT is said to be best kept at pH 6-8 and VS at pH 3.5-4 or below.contextual

Scope: reactive groups used in digital-textile reactive dyes

States MCT is most widely used for digital textile, with VS-type C.I. Reactive Black 5 widely used for deep black; both bond to cellulose OH groups under alkali. To suppress hydrolysis, MCT should be kept at pH 6-8 and VS at pH 3.5-4 or below.
Source: デジタルテキスタイル用色材 (城田衣(キヤノン株式会社 総合R&D本部), 2015) ・3.2 反応染料、3.4.1 インクの保存性 ・textbook ・ checked against the source by AI
reactive dye ・causesMCT- and VS-type reactive dyes behave differently over steaming time: while MCT's reaction is stabilising, VS dye has already begun a steep decline in fixation, so processing MCT-based colours (yellow/magenta/cyan) and VS-based black together under the same steaming conditions is said to readily cause colour drift (poor reproducibility) in the black.contextual

Scope: colour drift in black during the steaming stage for reactive ink

States that while MCT's reaction is stabilising, VS dye has already begun a steep decline in fixation; since other colours (yellow, magenta, cyan) are MCT-based, processing MCT and VS together under the same steaming conditions causes colour drift in black.
Source: デジタルテキスタイル用色材 (城田衣(キヤノン株式会社 総合R&D本部), 2015) ・3.4.2 蒸熱工程時の色ブレ、b)ブラックの色ブレについて ・textbook ・ checked against the source by AI
reactive dye ・propertyOne example reactive-ink printing workflow shows post-treatment as: high-temperature steaming (saturated steam, 102 degC for 8 minutes), followed by a 5-minute rinse, soaping (100 degC, 3 minutes), a warm rinse (60-80 degC) and a final rinse.contextual

Scope: one example of reactive-ink IJ-printing post-treatment

Figure-1 shows post-treatment as high-temperature steaming (saturated steam, 102 degC, 8 min), then a 5-min rinse, soaping (100 degC, 3 min, nonionic surfactant 1 g/L), a warm rinse (60-80 degC) and a rinse.
Source: デジタルテキスタイル用色材 (城田衣(キヤノン株式会社 総合R&D本部), 2015) ・図-1 反応インクのプリント工程 ・textbook ・ checked against the source by AI
reactive dye ・propertyThe fixation rate of reactive dye is said to be around 60-80% depending on the dye and its concentration, with the remaining 20-40% of dye going unfixed into the wash water, making wastewater treatment essential.contextual

Scope: fixation rate of reactive dye and wastewater

States that, depending on dye type and concentration, reactive dye fixation is 60-80%, with 20-40% of dye moving unused into the wash water, making wastewater treatment essential.
Source: 捺染業から見たインクジェット (伊藤高廣(Advanced Consulting Partners、元東海染工株式会社), 2016) ・7.洗浄工程と仕上工程 ・textbook ・ checked against the source by AI
reactive dye has the property of Colour bleeding ("iro-naki")contextual

Scope: Cellulosic materials such as cotton, reactive dyes

States reactive dyes are increasingly used on cellulosic materials like cotton, and that because their reactive group forms a strong covalent bond with the fibre's reactive groups, wet fastness is said to be comparatively good, but they are not a cure-all: hydrolysis of the reactive dye caused by moisture in the air during long-term storage is reported to cause bleed, with fixative (FIX-agent) treatment cited as one countermeasure.
Source: 第53回:ケーススタディ⑨色の変化~汚染・色泣き~(アパレル散歩道) (清嶋展弘(元・株式会社デサント。技術士(繊維)事務所。一般財団法人ニッセンケン品質評価センター発行コラム), 2023) ・「綿素材の汚染事故」 ・institutional summary ・ checked against the source by AI
reactive dye causes Colour bleeding ("iro-naki")contextual

Scope: Printed products using reactive dyes

States the symptom was that, after purchase, storage and pre-wear washing, colour bled from red printed polka dots; the cause is that the reactive dye used in the print hydrolysed, so washing moisture triggered bleed. Gives four countermeasures: selecting/using a reactive dye with good hydrolysis resistance; selecting/using a fixative (wet-fastness improver) suited to the dye; checking fabric performance in advance with a bleed test or a bleed test after accelerated hydrolysis (e.g. for colour-combination items); and avoiding storage in high-temperature, high-humidity environments.
Source: No487_より良いものづくりのために 染色・プリントの事故事例 -反応染料の加水分解による色泣き- (一般財団法人ボーケン品質評価機構, 2026) ・「現象」「原因」「対策」 ・institutional summary ・ checked against the source by AI
reactive dye ・causesStates the dye-mixing water should be a warm 98-105°F (about 37-41°C), with the exception of some black dyes (#250 Jet Black, #275 Hot Black) and #175 Neutral Grey, for which hot water is acceptable; using hot water makes the dye bond with the water and resist letting go to bond with the fabric, so more colour can end up washing out afterward. Also states some colours (e.g. Fuchsia) can congeal in cold water.contextual

Scope: Temperature at which the dye solution is prepared

States the ideal temperature for mixing/dissolving dye is 98-105°F (like a baby bottle, warm, never hot); hot water makes dye bond to it and not let go to bond with the fibre, so on rare occasions mixing dye in hot water instead of warm washes out more of the colour than usual, occasionally all of it. States, conversely, that some lots of the magenta Fuchsia (#13, MX-8B, Reactive Red 11) congeal in cold water, which can also cause trouble in mixes containing it.
Source: Troubleshooting Tie-dye (Dharma Trading Co., 2024) ・「Temperatures are Very Important」 ・manufacturer statement ・ checked against the source by AI
reactive dye ・propertyStates azo dyes carrying a free amino group (-NH2) can undergo methylolation on contact with free formalin, causing marked colour change, when the post-dyeing resin-finishing agent, its process, or the setting conditions after sewing are inappropriate; to prevent this, care is needed in finishing and sewing (including setting) after dyeing to avoid contact with free formalin under hot and/or acidic conditions. States that as an example reaching the consumer, there was a case of discolouration caused by formalin released from synthetic-resin buttons.contextual

Scope: Cotton goods dyed with azo reactive dyes bearing free amino groups

States azo dyes with a free amino group (-NH2) can undergo methylolation from formalin, causing marked colour change, seen when the post-dye resin-finishing agent/process or post-sewing set conditions are inappropriate. States prevention requires care, during finishing/sewing (including setting) after dyeing, to avoid contact with free formalin under hot and/or acidic conditions; states formalin trouble is almost always caught before sewing/setting, with the only notable consumer-facing example being discolouration from formalin released by synthetic-resin buttons.
Source: 反応染料で染色した綿製品の変退色と色泣き (安部田貞治(住友化学工業大阪製造所第一研究所), 1983) ・誌面P56「b.ホルマリン変色」 ・textbook ・ checked against the source by AI
reactive dye ・propertyStates that dyes of the metal-complex type (discussed in the part on the chromophore of reactive dyes) readily lose their metal (demetalation) to amino acids such as histidine in sweat, so the dye can change markedly on exposure to sweat, or sweat plus light; states treatment with oxygen bleach also causes demetalation and additionally promotes fibre embrittlement. For these reasons, states research and development of this type of metal-complex dye in Japan had (as of writing) been discontinued for about ten years, and the amount of existing metal-complex dye in use was gradually decreasing.contextual

Scope: Dyes made into metal complexes to protect the azo group (a 1983 review; it is in the part about improving the chromophore of reactive dyes, but this paragraph itself does not use the word "reactive")

States dyes protecting the azo group by introducing a metal-binding group (-OH, -OCH3, etc.) at the ortho position and forming a metal complex were developed, giving yellows, reds, blues and browns fast to sunlight and chlorinated water, but the metal in such dyes is readily stripped (demetalated) by amino acids such as histidine in human sweat, so the dye can change very markedly under sweat, or sweat plus light. Also states metal-complex-dyed items undergo demetalation when treated with oxygen bleach, which also promotes fibre embrittlement; for these reasons, R&D on this type of metal-complex dye in Japan had been halted for about ten years (as of writing), with usage of existing metal-complex dyes gradually decreasing.
Source: 反応染料で染色した綿製品の変退色と色泣き (安部田貞治(住友化学工業大阪製造所第一研究所), 1983) ・誌面P56「A.変退色の防止 a.アゾ基の安定性」 ・textbook ・ checked against the source by AI
reactive dye ・propertyPresents a table comparing the chlorine resistance of various azo dyes (half-life of decomposition by sodium hypochlorite), stating that introducing a sulfonic acid group at the position ortho to the azo group protects it, markedly improving chlorine fastness compared with dyes lacking a sulfonic acid group or having it elsewhere. States that because the sulfonic-acid version is also less affected by sweat or oxygen bleach, an azo group with an ortho sulfonic acid group gives a chromophore fast to chlorinated water and sunlight.contextual

Scope: Chemical structure of the chromophore of azo reactive dyes (position of the sulfonic acid group)

States table 5 shows various azo dyes' chlorine resistance as the half-life of decomposition by sodium hypochlorite, and that stability to active chlorine differs greatly depending on where the sulfonic acid group sits; introducing it ortho to the azo group protects the azo group, markedly raising chlorine fastness versus dyes with no sulfonic group or one elsewhere. States the ortho-sulfonic version is also unaffected by sweat or oxygen bleach, making such dyes chromophores fast to chlorinated water and sunlight.
Source: 反応染料で染色した綿製品の変退色と色泣き (安部田貞治(住友化学工業大阪製造所第一研究所), 1983) ・誌面P56「表5各種アゾ染料の耐塩素性(半減時間)」本文 ・textbook ・ checked against the source by AI
reactive dye ・requiresGives a pretreatment-agent formulation (total 1000 g) for Mimaki's reactive-dye ink (SPC-0357xx series): sodium alginate (Aikuma Senryo) 20 g, Sunflolen SN (Nicca Chemical) 50 g, sodium hexametaphosphate 10 g, urea 70 g, sodium bicarbonate 30 g, anti-reduction agent (liquid type) 15 g, and water 805 g; for prints needing back-penetration, an additional 0.5 g of Repitol G (Daiichi Kogyo Seiyaku) is added.contextual

Scope: Mimaki's TX23-series textile-ink guidance, reactive-dye ink recipe, Mimaki's original formulation (2006 edition document)

Gives the pretreatment-agent composition for the reactive-dye ink recipe (SPC-0357xx series): sodium alginate (Aikuma Senryo) 20 g, Sunflolen SN (Nicca Chemical) 50 g, sodium hexametaphosphate 10 g, urea 70 g, sodium bicarbonate 30 g, anti-reduction agent (liquid type) 15 g, water 805 g, total 1000 g; for prints needing ink back-penetration, an additional 0.5 g of Repitol G (Daiichi Kogyo Seiyaku) is added.
Source: 捺染インク 使用ガイダンス(TX23シリーズ) (株式会社ミマキエンジニアリング) ・p.11、5-1-1.「前処理剤の作成」《前処理剤組成》の表 ・manufacturer statement ・ checked against the source by AI
reactive dye ・applies tostates that it suits all natural fibres such as cotton, viscose rayon, wool and silk, but will not dye syntheticscontextual

Scope: Dharma's general description of its fiber reactive (Procion MX) dyes

States that fiber reactive dyes are suited to all natural fibres -- cotton, viscose rayon, wool and silk -- but will not dye synthetics.
Source: Fiber Reactive Dye: General Information (Dharma Trading Co.) ・記事本文冒頭「VERSATILE:」の段落 ・manufacturer statement ・ checked against the source by AI
reactive dye bonds via dyeing by covalent bondingcontextual
The paper places fibre-dye bonding for cellulosic-fibre dyes into three modes (citing ref. 1) and states that reactive dyes bond via the most stable, highest-energy of the three (covalent bonding), which gives excellent wet fastness.
Source: 染色技術者のための染料化学(その3)2. 反応染料 (今田邦彦, 2002) ・P119 §2.1 ・textbook ・ checked against the source by AI

Open questions (3)

What makes a reactive-dyed piece come out pale?🧪 testable at home

Factors named in checked sources: low pH (Dharma), slower below 70°F (Dharma), soda ash bulks up with moisture so the same volume does less (Burch), dye mixed with soda ash weakens over time (Dharma). Storage of dye powder and fabric finish or content are unchecked. Which matter, and how much, under home conditions?

How do rinse temperature and number of rinses affect later bleeding?🧪 testable at home

How much unfixed dye remains, and what happens when washed with a white cloth?

What other symptoms appear in the Boken accident-case series (No425-No486) issues not yet checked?

From the "past articles" list on Boken's No487 article, the URLs for 13 more issues in the same accident-case series were identified — No425 (disperse-dye migration/sublimation), No434 (flocking loss), No440 (foil peeling), No443 (delamination), No449 (fusing defects), No454 (possibly "iro-naki"/bleed, the site's own wording is ambiguous), No458 (sweat/light), No468 (bleaching), No471 (light fastness), No475 (tap water), and No481 (metal-induced discolouration) — but only No483 (rubbing) and No463 (isatin yellowing) have been checked so far; the rest have not yet been reviewed.

← Back to the entries list